GENERAL NOTES
- Only the Master code can be used to assign, change, or delete the secondary 4-digit user codes.
- The following steps must be done from outside the keypad program mode (normal operation)
- Each of these sequences must be executed with no pauses between keystrokes.
- Are you taking too long between Keystrokes?
- The keypad gives no confirmation or prompts until all keystrokes are completed.
- Do you have the right Authority?
- When assigning new codes you don't have to program authority attributes.
 Back To Top
ASSIGNING A NEW MASTER CODE
- At the keypad, enter Installer Code + 8 + 02 + 4-digit Master Code.
- The system master code is user# 02.
- You will get a single beep to verify the entry was accepted.
For example, if the installer code of 4112 wants to add a master code of 1234, in partition1, Key the following: 4112 802 1234
Back To Top
CHANGING AN EXISTING MASTER CODE (MASTER CHANGING ITSELF)
- At the keypad, enter Master Code + 8 + 02 + New Master Code + New Master Code.
- This will change the master code. The new code is keyed twice for verification.
- You will get a single beep to verify the entry was accepted.
For example, if the master code is 1234 and wants to change itself to 5678, Key the following: 1234 802 5678 5678
Back To Top
PROGRAMMING A SECONDARY USER CODE (CODES 03-32)
- At the keypad, enter Master Code + 8 + [user position] + 4-digit User Code.
- You will get a single beep to verify the entry was accepted.
- The user position will be a 2-digit entry of 03, 04, 05, etc.
For example, if the master code is 1234 and wants to add a code of 5678 as user#03, Key the following: 1234 803 5678
Back To Top
DELETING A SECONDARY USER CODE (CODES 03-32)
- At the keypad, enter Master Code + 8 + [user position] + # + 0.
- You will get a single beep to verify the entry was accepted.
- The user position will be a 2-digit entry of 03, 04, 05, etc.
For example, if the master code is 1234 and wants to delete user #03, Key the following: 1234 803 #0
Back To Top
ARE YOU USING THE PROPER CODE TO PROGRAM YOUR OTHER CODES?
- The installer can add user 02 (system master) only.
- The system master (User 02) can program any other system codes.
- Other codes may be changed to become master codes by keying:
Master Code + 8 + [user position] + # + 1 + 4
- You will get a single beep to verify the entry was accepted.
- The user position will be a 2-digit entry of 03, 04, 05, etc.
Back To Top
WHEN ASSIGNING NEW CODES YOU DON'T HAVE TO PROGRAM AUTHORITY ATTRIBUTES
- By default, code 02 is a system master. Codes 03, etc. are standard codes.
- By default, codes are not limited by time schedule.
- By default, all codes have paging enabled.
- You don't have to program attributes unless you want to change the above!
Back To Top
HOW TO CHANGE A USER AUTHORITY LEVEL
- Other codes may be changed to become master codes by keying:
Master Code + 8 + [user position] + # + 1 + [Authority level]
- You will get a single beep to verify the entry was accepted.
- The user position will be a 2-digit entry of 03, 04, 05, etc.
For example, if the master code is 1234 and wants to make user #03 a standard code, Key the following: 1234 803 #10
Authority Levels
0 = standard code
1 = arm only (maid code)
2 = guest
3 = duress
4 = partition master code
Back To Top
|
